embedded power for business-critical continuity hps35 series 350 - 1400 watts special features ? active power factor correction ? en61000-3-2 compliant ? cispr22, en55022 level-b conducted/radiated emi ? en61000 immunity standards ? 5v sb @2a ? overvoltage protection (ovp) ? overcurrent protection (ocp) ? overtemperature protection (otp) ? ac ok signal and indicator led ? dc ok signal and indicator led ? remote inhibit ? remote sense on main output ? hot plug ? n+1 redundant ? 2 year warranty total power: 350 watts per module input voltage: 90-264 vac # of outputs: single and standby safety input input voltage: 90-264 vac typical frequency: 47-440 hz inrush current: 40 a peak typical @ 25 c efficiency: 80% typ @ full load, 230 vac power factor: 0.98 typical @ 115 vac, full load turn-on time: ac on -2 sec., inhibit / enable 160 ms emi filter standard: cispr 22, en55022 level b leakage current standard: <0.5 ma max @ 230 vac @ 60hz (per module) radiated emi: cispr 22, en55022 level b holdup time: 20 ms minimum (independent of input vac) ac ok: 5 ms early warning minimum before outputs lose regulation harmonic distortion: meets en61000-3-2 isolation: meets en60950 output adjustability: 5% of nominal output voltage overall regulation: 3% ripple: 1% of vout pk - pk (20 mhz bandwidth) dynamic response: 4% from 25% to 75% load step recovery time: to within 1% in <300 sec overcurrent protection: 115 - 130% of rated output current short circuit protection: protected for continuous short circuit. auto recovery. overvoltage protection: 120 - 140% ac reset. reverse voltage protection: 100% of rated output voltage thermal protection: main and aux disabled when internal temp exceeds safe operating range remote sense: up to 0.5 v total drop single wire parallel: current share to within 10% of total rated current on main output dc ok: 5% of nominal ul ul60950-1, 1st ed. (april 1, 2003) csa csa c22.2 60950-1-03 tuv en60950-1:2001 (1st ed.) cb iec60950-1, 1st ed. (2001) ce mark (lvd) ? ? ? ? ? electrical specifications rev. 2.18.09_133 hps35 series 1 of 4
watts 350 input voltage 90-264 module id hps35 code volt output amps l 12.0 29.2 q 24.0 14.6 w 48.0 7.3 max. size ( h x w x l ) 1.6 x 4.3 x 10.5 number per rack 4 unit weight (lbs) 3.2 7. 6 53. 8 (all units in mm ) HPS35L-NNR-000 maximum output power is 350w da te: yyw w s/n: mmmmwwssssrrc made in philippines input : 90 - 240v ac - 40 a 50/60 hz serial no.: output : +12v / 29a rev : xx a/c code: xxxx 73-81 1-029 1 a b c d e f h j k l m n p r s t u v w x y z aa ab 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 to p side 1-24 pin no . 1 2 3 4 5 6 7 8 9 10 11 12 13 5v rt n co mmon co mmon co mmon co mmon co mmon co mmon ac (l ) blank swp gnd ac (n ) blank signal name +sense h co mmon p l n m k j co mmon co mmon co mmon co mmon co mmon signal name ac (l ) a d f e c b blank gnd -sense blank ac (n ) pin no . signal name ac ok tbd i2c da ta dc ok inhibi t x blank 20 23 24 22 21 fa n mon i2c clk +5v st andby tbd aa ab z y signal name +12v 14 17 19 18 16 15 pin no . r +12v u w v t s pin no . +12v +12v +12v +12v +12v +12v +12v +12v +12v +12v to p b ot to m to p b ot to m pin designa tion rev.2.18.09_133 hps35 series 2 of 4 environmental specifications modules HPS35L-NNR-000 12v hps35q-nnr-000 24v hps35w-nnr-000 48v ordering information module information pin assignments hps35 module bottom top pin description pin description 1 ac (l) 13 common 2 blank 14 v out 3 ac (n) 15 v out 4 blank 16 v out 5 gnd 17 v out 6 swp 18 v out 7 5v rtn 19 v out 8 common 20 blank 9 common 21 +5 standby 10 common 22 tba 11 common 23 fan mon 12 common 24 i 2 c clk pin description pin description a ac (l) p common b blank r v out c ac (n) s v out d blank t v out e gnd u v out f -sense v v out h +sense w v out j common x inhibit k common y tba l common z ac ok m common aa dc ok n common ab i 2 c data mating connector: edac 307-048-520-201 or equivalent rating: 5a per contact unit connector card edge connector with gold fingers double-sided 1.6mm fr-4 pcb operating temperature: 0 to 50 c ambient. derate each output 2.5% per degree from 50 to 70 c shock: operating: 4g, half sine, 22 ms minimum duration, all 6 faces non-operating: 30g, half since, 6 ms minimum duration, all 6 faces random vibration: operating: 1g rms, 20 min/axis non-operating: 2.5g rms, 20 min/axis humidity: 95% non-condensing storage temperature: -40 to +85 c temperature coefficient: 0.04% per c cooling internal dc fans
330. 2 343.2 13.4 468. 8 442. 0 31.7 6.0 3. 2 43.7 482.6 25.0 22. 0 date: yyw w s/n: mmmmwwssssrrc made in philippines rev: xx a/c code: xxxx 73-810-002 serial no.: maximum output power is 1400w input: 90 - 240vac - 40a 50/60 hz output : +12v / 29 a hpr1-00 1 19 20 37 slot 1 slot 2 6: inhibit 13: inhibi t 7: dc ok 14: dc ok 8: ac ok 15: ac ok 9: i2c address #1 16: i2c address 10: i2c address #2 17: i2c address 11: fan monitor 18: fan monito r 12: global ac ok 19: global inhibi t 23: not used 21: i2c data 22: sw p 20: i2c clk 2: (+) sens e 4: 5v (std-by) 5: not used 3: (-) sens e 1: 5v rtn (std-by) 30: not used 29: fan monito r 25: dc ok 27: i2c address 28: i2c address 26: ac ok 24: inhibi t slot 3 37: not used 36: fan monito r 32: dc ok 34: i2c address 35: i2c address 33: ac ok 31: inhibi t slot 4 + rt n + rt n pin designation ac cord: (north america) for all other countries, please contact factory. 1) quail electronics series 5050 or equivalent (15a/125v) supply end - nema 5-15p equipment end - iec 60320-c19 2) quail electronics series 5052 or equivalent (20a/125v) supply end - nema 5-20p equipment end - iec60320-c19 blank panel: astec p/n 73-686-000 watts 1400 (fully populated) input voltage 90-264 module id hps35 rack id hpr1 max. size ( h x w x l ) 1.75 x 19.0 x 13.0 module distribution (4 ea) hps35 standard size 1u unit weight (lbs) 8.6 d-sub connector pin outs pin description 1 5v return (std-by) 2 + remote sense 3 - remote sense 4 5v stand by 5 unused 6 module inhibit 7 dc ok 8 ac ok 9 i2c_add#1 10 i2c_add#2 11 fan monitor 12 global ac ok 13 module inhibit 14 dc ok 15 ac ok 16 i2c_add#1 17 i2c_add#2 18 fan monitor 19 global inhibit s l o t 1 pin description 20 i2c clock 21 i2c data 22 swp 23 unused (i2c_int) 24 module inhibit 25 dc ok 26 ac ok 27 i2c_add#1 28 i2c_add#2 29 fan monitor 30 unused 31 module inhibit 32 dc ok 33 ac ok 34 i2c_add#1 35 i2c_add#2 36 fan monitor 37 unused s l o t 2 s l o t 3 s l o t 4 psu connector 617-a-037-p-aj-1-21 (male socket) amphenol pin out diagram d-sub connector (male) mating connector 617-a-037-s-aj-1-20 (female socket) amphenol pin out diagram d-sub connector (female) rev. 2.18.09_133 hps35 series 3 of 4 hpr1-00 racks rack information
embedded power for business-critical continuity pin 2 + remote sense pin 3 - remote sense compensates for up to 0.5v drop. recommended shielded twisted wire pair. pin 12 - global ac ok (out signal) note: ac ok signals are ored together internally. if any module fails, the led on the affected module will be off and the logic signal will indicate ac not ok. pin 19 - global inhibit (in signal) note: all outputs disabled when pin 19 is open or high. pin 22 - swp (in/out signal) swp pin is used when connecting racks in parallel to achieve current sharing. current share accuracy is typically 10% of full load. note: swp voltage is 5v at 100% load current. module inhibit (in signal) note: module inhibit signals for each slot in the rack is accessible in the d-sub connector (j18). refer to connector pin-out table for pin assignments. pin 1 is the return pin. dc ok (out signal) note: dc ok signals for each slot in the rack is accessible in the d-sub connector (j18). refer to connector pin-out table for pin assignments. pin 1 is the return pin. ac ok (out signal) note: ac ok signals for each slot in the rack is accessible in the d-sub connector (j18). refer to connector pin-out table for pin assignments. pin 1 is the return pin. hi state: source 100ua @ 4v low state: sink 10ma @ 0.5v fan monitor (out signal) note: fan monitor signals for each slot in the rack is accessible in the d-sub connector (j18). refer to connector pin-out table for pin assignments. pin 1 is the return pin. i2c_add#1 i2c_add#2 tbd rev.2.18.09_133 hps35 series 4 of 4 americas 5810 van allen way carlsbad, ca 92008 usa telephone: +1 760 930 4600 facsimile: +1 760 930 0698 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom telephone: +44 (0) 1384 842 211 facsimile: +44 (0) 1384 843 355 asia (hk) 14/f, lu plaza 2 wing yip street kwun tong, kowloon hong kong telephone: +852 2176 3333 facsimile: +852 2176 3888 for global contact, visit: www.powerconversion.com techsupport.embeddedpower @emerson.com while every precaution has been taken to ensure accuracy and completeness in this literature, emerson network power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. emerson network power and the emerson network power logo are trademarks and service marks of emerson electric co. ?2008 emerson electric co. emersonnetworkpower.com embedded computing embedded power monitoring outside plant power switching & controls precision cooling racks & integrated cabinets services surge protection emerson network power. the global leader in enabling business-critical continuity. ac power connectivity dc power d. sub connector additional notes pin 22 pin 3
|
